SXVGA, Color Camera
The STC-TC133USB-AH is a compact, progressive scan, SXVGA, USB cased camera with a 1/3” color CCD, featuring 22fps, software and hardware triggering, image capture, digital zoom and a feature-rich user based menu setup and control. This cased camera is the same as the ASH model except that the USB signal is output over the USB connector. Sentech USB cameras include a SDK, DirectX, Twain and Linux driver, as well as the Sentech Viewing Software.
· 1/3" CCD Image Sensor, SXVGA (1.25 MP)
· Output over USB Connector, 22fps
· Hardware & Software Trigger
Name |
Specifications |
Model No |
STC-TC133USB-AH |
Imager |
1/3” Interline SXVGA Color Progressive CCD: ICX445AQ |
Total Picture Element |
1348 (H) x 976 (V) |
Active Picture Element |
1296 (H) x 966 (V) |
Chip Size |
6.26 (H) x 5.01 (V) mm |
Cell Size |
3.75 (H) x 3.75 (V) µm |
Scanning System |
Progressive |
Scanning Methods |
Full Scanning, 1/1 Partial Scanning, 1/2 Partial Scanning, 1/4 Partial Scanning, Variable Partial Scanning |
Pixel Frequency |
36.818 MHz (Normal) / 18.4090 MHz (1/2 clock) / 9.20453 MHz (1/4 clock) |
Maximum Frame Rate |
- |
- Full Scanning |
22.40 fps (Normal) / 11.20 fps (1/2 clock) / 5.600 fps (1/4 clock) |
- 1/2 Partial |
44.81 fps (Normal) / 22.40 fps (1/2 clock) / 11.20 fps (1/4 clock) |
- 1/4 Partial |
89.80 fps (Normal) / 44.90 fps (1/2 clock) / 22.45 fps (1/4 clock) |
Resolution |
1280 (H) x 960 (V) (Full Scanning) 1280 (H) x 440 (V) (1/2 Partial Scanning) 1280 (H) x 168 (V) (1/4 Partial Scanning) |
S/N Ratio |
≤ 10 digit (Factory Default Gain Setting) |
Minimum Scene Illumination |
3.94 Lux at F1.2 |
Sync System |
Internal |
Electronic Shutter |
Auto / Manual (Software Selectable) |
- Normal |
1/36,818182 to 1/22.40 seconds |
- 1/2 Clock |
1/18,409,091 to 1/11.20 seconds |
- 1/4 Clock |
1/9,204,545 to 1/5.60 seconds |
Gain |
Auto / Manual (Software Selectable) |
Gamma |
Manual (Software Selectable) |
White Balance |
Auto / Manual / One shot (Software Selectable) |
Trigger Mode |
Free-run / Edge Preset Trigger / Pulse Width Trigger / Start & Stop Trigger (Software selectable) |
Input / Output |
USB2.0 High Speed |
Power |
- |
- Input Voltage |
+5 Vdc through USB connector or 12Pin connector |
- Consumption |
Less than 430 mA |
Dimensions |
50 (W) x 50 (H) x 35.8 (D) mm |
Lens Mount |
CS Mount |
Input / Output Connector |
12 Pin Connector (Hirose) / 2.5 mm Pin Jack |
Tripod |
1/4”-20UNC depth 7 screw hole on top and bottom case, 4-M4 depth 4 screw holes on top, bottom and both side of case |
Weight |
Approximately 112g |
Operating Temperature |
0 to 40 deg. C |
Storage Temperature |
-30 to 65 deg. C |
Vibration |
20 Hz to 200 Hz to 20 Hz (5 min. /cycle), acceleration 10G, 3 directions 30 min. each |
Shock |
Acceleration 70G, half amplitude 6 ms, 3 directions 3 times each |
Standard Compliancy |
EMS :EN61000-6-2, EMI :EN61000-6-3 (Class B) |
RoHS |
RoHS Compliant |